MK1 swe Exam Study Guide 672 Questions with Complete Solutions Latest Updated 2024/2025 When is the cutter engineering report due? - Correct Answer Jan 31 What type of engine is on a P100 - Correct Answer Single cylinder air cooled four stroke How long will a P6 pump run on a tank of fuel - Correct Answer 4 hours What type of engine is on a P6 pump - Correct Answer 6.5 horsepower Honda GX-200 has engine How would you test 4-20 mA sensor - Correct Answer In series The MPU - 23 card exhibits what color lights on the panel when operating normally - Correct Answer Green Yellow Yellow How many digits are in a NSN - Correct Answer 13 What cut are R/G teeth? - Correct Answer helical Oil fog out of R/G - Correct Answer Faulty precipitator Standard hoses shall be identified as Standard in Hose Log and shall be scheduled for replacement at intervals not to exceed - Correct Answer 8 years What % hydraulic failure is due to contamination? - Correct Answer 80% Hoses installed in the weather without an outer covering specifically designed for service in the weather shall have a service life not to exceed - Correct Answer 5 years When using an ammeter to troubleshoot a system always use what - Correct Answer The highest scale 1 / 4
Small engine exhaust hose service life shall be in accordance with the hose manufacturer recommendation or - Correct Answer 5 years whichever is less The most common type of media for coarse filtration is - Correct Answer Surface media What is the disadvantage of a centrifugal pump - Correct Answer Suction lift The shelf life for hoses and prefabricated hose assemblies shall not exceed - Correct Answer 10 years As wire size increases, what happens to resistance and amperage? - Correct Answer Resistance down - Amperage up What does CAN stand for? - Correct Answer Controller Area Network What % of working pressure do you test a temp hose - Correct Answer 150 How does a rise in the R/O input water temp effect the output temp - Correct Answer Output increases What coolant is used in a keel cooler? - Correct Answer antifreeze At a modernized unit, where is your boat inspection report recorded? - Correct Answer ALMIS How often is the cutter engineering report conducted - Correct Answer Yearly Rudder stock is supported by what? - Correct Answer bearing Waster ring in the sea chest is for what? - Correct Answer prevent galvanic corrosion 2 / 4
What is the acceptable leakage rate in a screw type hydraulic pump shaft seal - Correct Answer 50ml If you have a bearing failure in a centrifugal pump with excessive vibration, what is the likely cause? - Correct Answer misalignment What causes aeration in a hydraulic system if there are no leaks? - Correct Answer low fluid You find something else is wrong with a piece of equipment already CASREPed what should you send? - Correct Answer Update A thrust bearing supports what type of movement - Correct Answer axial and radial What does SSS stand for in a SSS clutch? - Correct Answer Syncro-Self-Shifting How is tin measured in a spectrometric oil analysis? - Correct Answer ppm If you find 40psi in a TANB trailer tire what type of discrepancy is it? - Correct Answer restrictive Where can DEMPS procedures be found? - Correct Answer NEM-233-11 What type of fuel does a P100 run on - Correct Answer F76 and JP5 When do you have zincs in freshwater - Correct Answer Never What is considered a hot surface on piping requiring flange shielding for LO - Correct Answer 650 What is considered a hot surface on piping requiring flange shielding for FO - Correct Answer 400 What happens to hydraulic oil for every 18 degrees it rises above 140 - Correct Answer Oxidation rate doubles 3 / 4
What type of o-ring is the most resistant to petroleum products - Correct Answer Buna-S Before you inflate a shaft seal what must you do first - Correct Answer Stop and lock shaft After an oil and filter change how many hours of engine operation should be allowed before sampling - Correct Answer 25 hours Check amps on a non clamp ammeter - Correct Answer In series How is the boat record kept in a modernized unit - Correct Answer EAL What is the max thickening and dilution of L/O - Correct Answer 40% thickening, 5% dilution Oil intervals on a R/G - Correct Answer 500 hours what should the chlorine levels on the potable water shore tie be - Correct Answer .02ppm for 15min or .02ppm for 30min What date is placed on the hose tag - Correct Answer Replacement Jacket water is tested - Correct Answer monthly What type of fuel has FSII - Correct Answer F44 what size safety chains are used on an rbs trailer - Correct Answer 1/2" What PMS does not show up in the Cutter engineering report - Correct Answer Daily and weekly
- / 4